DuraFlex Chimney Cleaning Service in Gravesend, NY

Gas fireplace serviceGas fireplace service
Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Why Gravesend Homeowners Choose DuraFlex Chimney Cleaning

We provide independent DuraFlex chimney cleaning in Gravesend: Level 2 inspection, creosote removal, and cap and joint service on DuraFlex flexible stainless liners, including diagnostic work on the Pro Stainless Steel Liner, the Premium Flexible Chimney Liner Kit, insulated liner and wrap assemblies, and rigid stainless pipe sections. What sets our DuraFlex work apart is that we check the parts most sweeps never look at closely – the tee, the appliance connector, the top plate – because on rowhouse installs those are where these liners actually fail. We are an independent DuraFlex service provider and are not affiliated with, authorized by, or endorsed by DuraFlex. Our technicians have up to 15 years of experience. For DuraFlex work in Gravesend, call (855) 342-5978.

Call (855) 342-5978

Why Trust Chimney Sweep Gravesend for Your DuraFlex Chimney Cleaning?

A flexible stainless liner is not a firebox, a flue tile, or a steel chimney pipe, and servicing one takes a different set of habits. Our technicians have handled DuraFlex components enough times to know where the weaknesses sit: the compression fitting where a flexible section lands on an appliance connector, the tee at the base of an offset, the seal at the top plate. We read the signs in order. Rattle, soot smell, water staining on the ceiling below the stack.

We repair and service DuraFlex equipment with quality parts that fit it, and we don’t pretend to be a DuraFlex dealer or to hold DuraFlex certification. When a connector or tee needs replacement, we use DuraFlex-compatible OEM parts where the liner is sound and an aftermarket component only when the match is exact and the original is no longer made. We don’t stock DuraFlex parts, and we never claim to.

The same independent stance applies to HeatShield and Gelco, our other two main product lines in Gravesend. Because we’re not tied to one manufacturer, a recommendation follows what your flue needs. Warranty-safe practice matters here too: we document what we find by camera and photo before we touch anything, so a DuraFlex liner that’s still under coverage isn’t modified in a way that creates a problem later. Call (855) 342-5978 to talk through your liner.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Common DuraFlex Chimney Cleaning Problems We Fix in Gravesend

  • Liner joint separation at the appliance connector or tee. The seam between a flexible DuraFlex section and the connector or tee is the most common failure we find. Creosote and condensate work past a loosened joint, and the first symptom owners notice is a soot smell that comes back within days of a sweep. Re-securing or replacing the joint closes it.
  • Rust-through on 304-alloy liners serving wood or oil appliances. A 304 liner is a reasonable match for a gas appliance, but used with wood or oil it can rust through where condensate pools at the bottom of the flue. Once the alloy is pitted through in a section, patching is a short-term fix and replacement is the honest recommendation.
  • Crushed or kinked flexible liner from a prior install. A flexible liner forced around an offset or through a tight flue can kink at the bend. A kinked section narrows the path, cuts draft, and traps soot where the bend narrows. A camera run tells us whether the liner is kinked, and by how much.
  • Corroded or disconnected top plate and cap assembly. The termination at the top of a DuraFlex run is exposed to everything the weather sends. A corroded or disconnected top plate lets water into the liner annulus, which shows up as damp insulation, staining at the crown, or a wet flue after a storm. Cap replacement and top plate work go together here.
  • Blocked or restricted flue from accumulated creosote behind a failed joint. When creosote leaks past a separated seam it collects in a pocket that a routine sweep can miss. We clean the flue path only after confirming it’s intact, then remove the creosote from the full run.

DuraFlex Parts & Our Repair-vs-Replace Approach

Parts choice on a DuraFlex liner is a match problem, not a brand loyalty problem. We use DuraFlex-compatible OEM connectors, tees, top plates, and caps where the existing liner is sound, because a proper fit is what keeps a joint sealed. When an OEM part is discontinued, we substitute a quality aftermarket component only where the match is exact. We don’t stock DuraFlex parts and we won’t claim to.

Repair-versus-replace comes down to the alloy and the damage pattern. A cracked top plate, a separated tee, or a cap that’s lost its seal is a repair – the liner itself is still doing its job. Rust-through on a 304 liner used with a wood appliance is different: once the wall is pitted through, a patch buys time and nothing more, and saying so is the right call. A crushed section from a prior install gets evaluated on how much draft it’s costing, not on appearance. Call (855) 342-5978 and we’ll walk you through what your liner actually needs.

Our DuraFlex Service Process – Step by Step

  1. 1
    Level 2 inspection. Before any cleaning, we run a camera through the flue path and check the appliance connector, the tee, and the top termination. On a DuraFlex liner this is where we confirm alloy, look for kinks, and check that every joint is closed.
  2. 2
    Diagnosis. We photograph what we find and show you the images. A separated seam, a rusted section, a crushed bend, a corroded top plate – each one gets named and tied to what causes it.
  3. 3
    Repair or replacement. Connectors, tees, top plates, and caps get re-secured or replaced with parts that fit. If the liner alloy is already failing, we’re direct about replacement instead of selling a patch.
  4. 4
    Creosote removal. The liner gets swept only after the flue path is confirmed intact, so we don’t drive soot into a pocket behind a failed joint.
  5. 5
    Test. We check draft and confirm the termination is sealed before we leave, with a photo record of the before and after.
  6. 6
    Warranty-safe documentation. Everything we touched is recorded so a later service or a warranty discussion has a clear history.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

DuraFlex Products We Service & Install in Gravesend

We service and install DuraFlex flexible stainless steel liners used for wood, gas, and oil appliances. That includes the DuraFlex Pro Stainless Steel Liner in 316L and 304 alloy, the DuraFlex Premium Flexible Chimney Liner Kit, the DuraFlex Insulated Liner with its wrap kit, and DuraFlex rigid stainless pipe sections and fittings where a run needs a rigid section.

We also handle cap replacement, top plate work, and creosote removal on these systems. If your Gravesend liner needs a Level 2 inspection first, that’s where we start. We don’t claim to stock DuraFlex parts; we service and install with parts that fit.

We Also Service These Brands

DuraFlex is one line we work with, not the only one. We also work with HeatShield, the ceramic resurfacing system used for liner repair, and Gelco, along with Olympia Chimney, Famco, and Copperfield. That range matters in Gravesend because a rowhouse chimney stack often has more than one product in play. A durable recommendation follows the flue, not one manufacturer’s parts catalog.

FAQs – DuraFlex Chimney Cleaning Service in Gravesend

Book Your DuraFlex Service in Gravesend, NY

If you own a DuraFlex liner and want it inspected by someone who knows where these systems fail, call Chimney Sweep Gravesend at (855) 342-5978. We’re an independent service provider for DuraFlex, HeatShield, and Gelco, and we handle the full job: Level 2 inspection, creosote removal, cap and tee replacement. Call (855) 342-5978. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. The estimate is free.

Written by the team at Chimney Sweep Gravesend.

Need Chimney Cleaning help nationwide? Licensed & insured · free written estimates
Call (855) 342-5978
Local Service Coverage
Chimney Sweep GravesendChimney Sweep BensonhurstChimney Sweep Sheepshead BayChimney Sweep Brighton BeachChimney Sweep Coney IslandChimney Sweep MidwoodChimney Sweep Dyker HeightsChimney Sweep FlatlandsChimney Sweep Borough ParkChimney Sweep Marine ParkChimney Sweep Mill BasinChimney Sweep Bergen BeachChimney Sweep KensingtonChimney Sweep Bay RidgeChimney Sweep FlatbushChimney Sweep Sunset ParkChimney Cap & Crown GravesendChimney Cap & Crown BensonhurstChimney Cap & Crown Sheepshead BayChimney Cap & Crown Brighton BeachChimney Cap & Crown Coney IslandChimney Cap & Crown MidwoodChimney Cap & Crown Dyker HeightsChimney Cap & Crown FlatlandsChimney Cap & Crown Borough ParkChimney Cap & Crown Marine ParkChimney Cap & Crown Mill BasinChimney Cap & Crown Bergen BeachChimney Cap & Crown KensingtonChimney Cap & Crown Bay RidgeChimney Cap & Crown FlatbushChimney Cap & Crown Sunset ParkChimney Repair GravesendChimney Repair BensonhurstChimney Repair Sheepshead BayChimney Repair Brighton BeachChimney Repair Coney IslandChimney Repair MidwoodChimney Repair Dyker HeightsChimney Repair FlatlandsChimney Repair Borough ParkChimney Repair Marine ParkChimney Repair Mill BasinChimney Repair Bergen BeachChimney Repair KensingtonChimney Repair Bay RidgeChimney Repair FlatbushChimney Repair Sunset ParkFireplace Repair GravesendFireplace Repair BensonhurstFireplace Repair Sheepshead BayFireplace Repair Brighton BeachFireplace Repair Coney IslandFireplace Repair MidwoodFireplace Repair Dyker HeightsFireplace Repair FlatlandsFireplace Repair Borough ParkFireplace Repair Marine ParkFireplace Repair Mill BasinFireplace Repair Bergen BeachFireplace Repair KensingtonFireplace Repair Bay RidgeFireplace Repair FlatbushFireplace Repair Sunset ParkChimney Inspection GravesendChimney Inspection BensonhurstChimney Inspection Sheepshead BayChimney Inspection Brighton BeachChimney Inspection Coney IslandChimney Inspection MidwoodChimney Inspection Dyker HeightsChimney Inspection FlatlandsChimney Inspection Borough ParkChimney Inspection Marine ParkChimney Inspection Mill BasinChimney Inspection Bergen BeachChimney Inspection KensingtonChimney Inspection Bay RidgeChimney Inspection FlatbushChimney Inspection Sunset Park

Request a Free Estimate in Gravesend

Tell us what you need - Chimney Sweep Gravesend responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - We Answer 24/7