Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Fast, Reliable Chimney Cap & Crown Across Mill Basin
If your cap is rusting through or your crown is dropping mortar, we can help. Chimney Sweep Gravesend installs and repairs chimney caps and crowns for Mill Basin homeowners, from the bay side streets off Belt Parkway to the inland blocks near Avenue U. We know this neighborhood’s housing: low-slung postwar ranches, brick-and-frame splits, exterior flues run short and offset, and plenty of fireplaces added after the house was built. That matters because cap and crown work here has to survive salt air and bay humidity, not just rain. Call (855) 342-5978. We answer 24/7. Fast dispatch, 7am-7pm.

Why Mill Basin Homeowners Call Chimney Sweep Gravesend for Chimney Cap & Crown
We’re chimney and fireplace specialists, not a general handyman outfit squeezing in one more trade. That focus shapes every cap and crown call in Mill Basin. Our technicians have up to 15 years of experience, and our inspections are informed by hands-on repair work rather than a checklist someone fills out between other jobs.
Homeowners on the larger properties around Mill Basin tend to call us back because one company handles the whole chimney: sweep, inspection, cap, crown, repair, and fireplace work. No handing you off to a second contractor halfway through. We work with professional-grade brands – Copperfield, DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco – because materials matter as much as labor, especially where salt air eats standard hardware.
Response time to Mill Basin is quick, and we know the blocks. We’re familiar with the tight one-and-two-story rooflines here, where a cap that looks fine from the driveway can be hiding a cracked crown behind the parapet. That local familiarity is worth more than a low bid from someone who’s never set a ladder on filled marsh.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Our Chimney Cap & Crown Services in Mill Basin
Cap Installation
A new cap on a Mill Basin chimney should be stainless or copper, not the galvanized model that rusts through in a few seasons near the bay. We fit caps to the actual flue opening, not a one-size-fits-all size. On the short, offset flue runs common in Mill Basin ranches, getting the fit right keeps water and animals out without choking the draft.
Cap Replacement
When a cap has corroded or a storm has knocked it loose, replacement is usually a single visit. We pull the old cap, check the flue tile for cracking underneath, and set a new one sized to the flue. On Mill Basin homes with several flues, this is where we often find the second flue was left uncapped for years.
Crown Repair
A spalling crown is the most common masonry failure we see on Mill Basin’s 1950s-70s brickwork. We rebuild cracked and crumbling crowns so water sheds away from the chimney instead of soaking into the masonry. Given the bayfront humidity here, a crown that fails early tends to go unnoticed until a ceiling stain appears below.
Crown Coating
For a crown that’s sound but showing hairline cracks, a flexible, UV-stable coating can seal it without a full rebuild. On the low-pitch roofs around Mill Basin, this is often the sensible spec, and it holds up better against salt air and freeze-thaw than a rigid patch. We tell you honestly when coating will do and when the crown needs rebuilding.
We also install multi-flue and custom caps for the larger Mill Basin properties with several fireplaces or a converted insert. If you’d like the full scope of what our chimney cap & crown team handles, it’s laid out there.

Trusted Brands We Service in Mill Basin
We install and service products from Copperfield, DuraFlex, HeatShield, Gelco, Olympia Chimney, and Famco – names that mean something in the professional chimney trade, not big-box substitutes. That range lets us spec a cap or crown component that actually fits your flue and your exposure, whether that’s a copper cap for a bayfront chimney or a HeatShield repair where the liner needs resurfacing before a new crown goes on. We don’t claim to stock parts on a truck; we specify the right component for the job and get it done. If your cap or crown needs a material upgrade, we’ll tell you why and what it costs.
Common Chimney Cap & Crown Problems We See in Mill Basin Homes
- Rusted-out galvanized caps. Salt air off Jamaica Bay corrodes standard galvanized caps within a few seasons, letting water into exterior-mounted flues. Stainless or copper is the only spec that lasts here.
- Spalling crown mortar. Common on 1950s-70s brickwork, crowns crack and drop debris that can block the flue. On Mill Basin’s filled-marsh soil and bayfront humidity, this happens within a decade, often before the fireplace is ever lit.
- Undocumented, unlined flues. Many Mill Basin fireplaces were added by an owner or a local mason with little paperwork, so crown leaks go unnoticed behind sound-looking brick until a ceiling stain shows up.
- Undersized multi-flue caps. Homes with two fireplaces or a gas insert often have a cap sized for one appliance, leaving the second flue open to rain and animals.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Cap & Crown in Mill Basin, NY
Cap and crown work is priced per job by a written estimate, and the estimate is free. Typical ranges for Mill Basin, where salt air pushes most homeowners toward stainless or copper: a standard stainless or copper cap runs roughly $250-$550 installed, depending on flue size and access. A multi-flue or custom cap for a home with two fireplaces lands around $450-$900. Crown repair, including rebuilding a spalled crown, typically runs $350-$900, while a crown coating on a sound crown is often $200-$450. What moves the number is roof access, the condition of the flue tile underneath, and whether a Level 2 inspection turns up a liner issue. On a low-slung Mill Basin ranch the access is usually straightforward. On the taller custom waterfront homes it takes more setup. We put the flat price in writing before any work starts, so there are no surprises when the bill comes.
We Also Serve Cities Near Mill Basin
The same cap and crown work we do in Mill Basin covers the neighboring communities too. We serve Bergen Beach, Marine Park, Flatlands, and Sheepshead Bay, each with its own mix of housing stock and chimney exposure. If you’re just over the line in one of these areas, the call is the same and the standard doesn’t change.
Serving Mill Basin, NY – Our Local Coverage Area
We serve Mill Basin and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Chimney Cap & Crown in Mill Basin
Yes. A two-fireplace Mill Basin home usually needs a multi-flue cap sized to both flue openings, not a single-flue cap. When only one flue is capped, the second stays open to rain, salt air, and animals, which is a frequent find in homes here with a fireplace added after the original build. We measure both flues and spec a cap that covers them together. Call (855) 342-5978 for an exact quote – estimates are free.
Because a rigid patch over a moving, spalling crown doesn’t address why it cracked. On Mill Basin’s filled-marsh soil and bayfront humidity, masonry crowns expand and contract and take constant moisture, so hairline cracks reopen and small patches fail within a season or two. The fix is either a flexible, UV-stable crown coating on a sound crown or a full rebuild that sheds water properly. We look at the crown and the flue before recommending either. Call (855) 342-5978 for a free estimate.
Yes. Exterior-mounted flues are common on the low-slung postwar ranches around Mill Basin, and they can absolutely be capped. The cap has to be sized to the flue tile and anchored so it stays put through nor’easters and coastal storms, which hit these exterior chimneys hardest. We check the flue top for cracking first, since water tracking down an exterior run is often the reason a ceiling stain shows up inside. Call (855) 342-5978 for an exact quote – estimates are free.
Yes, and arguably more. A gas insert still vents through the chimney, and a failed cap or crown lets water and salt air into the flue and rusts the damper and venting. On Mill Basin homes with a gas conversion, we often find the original cap was left undersized for the new appliance, or the crown was never repaired after the conversion. Both are worth fixing before they turn into a liner problem. Call (855) 342-5978 for a free estimate.
Once a year is the standard for a home with multiple flues or a converted appliance, and Mill Basin’s salt air and long heating season make that annual check more useful here than in drier inland areas. A Level 2 inspection looks at the flue liner and smoke chamber, not just the cap, which matters on the owner-built fireplaces common in this neighborhood where the flue may be unlined or clay-tile. It’s also how a failing crown gets caught before a ceiling stain does. Call (855) 342-5978 for an exact quote – estimates are free.
Get Your Mill Basin Cap and Crown Checked
Salt air and bay humidity are hard on caps and crowns, and a small failure now is a liner repair later. Whether it’s a single-flue ranch or a multi-fireplace waterfront home, we’ll inspect it, show you what we find, and give you a written flat price before any work begins. Nothing gets recommended without evidence you can see for yourself, and we’ll tell you plainly when a repair can safely wait. Call (855) 342-5978. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Gravesend.