Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Gravesend Homeowners
A missing or rusted-through cap is one of the quietest problems a chimney can have, and one of the most expensive to ignore. Rain runs straight down a bare flue, birds and squirrels nest in it, and the crown underneath slowly cracks with every freeze and thaw. Our technicians have up to 15 years of experience fitting caps and rebuilding crowns, and because we do chimney work and nothing else, the inspection that finds the problem is the same visit that fixes it. We work with trade-grade materials from names like Copperfield and Gelco, not hardware-store substitutes. If a cap is loose, bent or gone, call (855) 342-5978 and we’ll book you in for a same-day visit where the schedule allows.
What Our Chimney Cap & Crown Service Includes
Caps and crowns are two different parts of the same weatherproofing job. The cap sits on top of the flue and keeps rain, animals and sparks out. The crown is the concrete or mortar slope at the very top of the masonry that sheds water away from the brick. One protects the flue, the other protects the chimney structure, and in Gravesend we usually find they fail together.
Cap Installation
A cap is a fitted cover over the flue opening, usually stainless steel or copper with a mesh screen around the sides. You need one on any chimney that doesn’t have a cap, or on a flue that was left open after a stove was removed. We measure the flue, choose a cap sized to the actual opening rather than a universal bracket, and secure it so wind can’t lift it off the masonry.

Cap Replacement
Replacement makes sense when an existing cap is rusted through, dented, missing screen panels, or sitting loose on a flue it was never sized for. A failing cap lets water and animals in while the rusted mesh stops doing its job on sparks. We pull the old cap, check the flue tile edges underneath for chipping, and set a new one with the correct clearances.

Crown Repair
The crown is the sloped concrete cap at the top of the masonry, and cracks in it let water soak into the brick and the mortar joints below. You need crown repair when you can see cracking from the ground or when a chimney inspection finds the slope has flattened and stopped shedding. We rebuild or patch the crown to restore the slope and bond it back to the flue, using a mortar mix suited to the freeze-thaw swing New York gets.

Crown Coating
Crown coating is a flexible, waterproof membrane applied over a crown that’s sound but showing hairline cracks. It’s the right call when the concrete is still intact and doesn’t need to come off. We clean the surface, fill the small defects, and coat the whole crown so water runs off instead of working into the seams.
Multi-Flue Cap
A multi-flue cap covers two or more flue openings on one chimney with a single unit, which is common on the wider chimneys you see on Gravesend’s older brick homes. You need one when separate single caps look cluttered, or when each flue has its own cap but the masonry between them is exposed. We build the unit to the full footprint of the chimney top so the whole crown area stays covered.
Custom Cap
Some chimneys have an unusual shape, an oversized flue, or a stone or stucco top that off-the-shelf caps won’t fit without looking bolted on. A custom cap is fabricated to the exact measurements of your chimney. We take the dimensions on site and have the cap made to match, in copper or stainless depending on the look you want and how the chimney is built.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with a short list of chimney-product makers we trust, and we name them because materials matter as much as labor. Copperfield makes caps and related chimney components in copper and stainless, and we fit their products on a wide range of Gravesend homes where the finish has to hold up to years of wet winters. Gelco products come up often on cap and crown work too, and we know where those components tend to wear first so we can check them as part of the inspection rather than after they fail.
DuraFlex is a name we see a lot in liner systems, and a cap sits right on top of that liner, so we’re used to making the two work together without disturbing the flue. HeatShield is the ceramic resurfacing system we use when the liner beneath the cap needs restoration, and it changes what we recommend at the top of the chimney because the cap and crown have to protect a repaired flue properly. Whether you have Copperfield, Gelco or any other make, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Water in the firebox after rain. Damp firebrick, a rusty damper, or a puddle on the smoke shelf usually means the cap is missing, undersized, or rusted through. Water in the firebox also loosens creosote, which makes the chimney harder to sweep cleanly.
- Cracks or crumbling concrete at the top. If you can spot a split in the crown from the ground with binoculars, water is already getting in. Left alone, the freeze-thaw cycle widens the crack each winter until the crown has to be rebuilt rather than repaired.
- Birds, squirrels or nesting debris in the flue. An open or uncapped flue is an invitation, and nests block the draft your fireplace depends on. A proper cap with mesh stops animals from getting in without restricting airflow.
- A cap that’s tilted, loose or dented. Wind can lift a badly fitted cap, and a loose cap bangs against the flue tile and can chip it. A dented mesh also traps creosote and stops doing its spark-arresting job.
- Staining or efflorescence on the upper brick. White powdery stains or dark streaks near the top of the chimney point to water soaking in from a failed crown or a poor seal at the cap. Catching it early keeps the repair to the crown instead of a larger masonry job.
Our Chimney Cap & Crown Process – Step by Step
- 1
Book the visit. Tell us what you’ve noticed and we’ll set a time. We answer 24/7 on the phone, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed Saturday.
- 2
Inspect from the ground and at the top. We look at the crown, cap, flue tiles and the upper masonry, checking for cracks, rust and loose mortar. Where a liner is involved, a camera inspection shows the flue’s condition so recommendations are based on what we see, not a guess.
- 3
Show you the findings. We explain what we found, photograph the problem areas where possible, and tell you plainly which items need fixing now and which can safely wait. Nothing gets recommended without evidence you can look at yourself.
- 4
Give you a written, flat-price estimate. You get the price before any work starts, agreed in writing. No surprise add-ons once the cap comes off or the crown is opened up.
- 5
Do the work and clean up. We install or replace the cap, repair or coat the crown, and check the seal before we leave. The job ends with the chimney top watertight and the work area cleared.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Gravesend?
Cost depends on which part of the job you need and how much access the roof allows. These are typical estimated ranges for the Gravesend market; your written estimate sets the final price.
| Service | Typical Estimated Range | What Drives the Price |
|---|---|---|
| Standard cap installation (single flue, stainless) | $180 – $350 | Flue size, cap type, roof pitch and access |
| Cap replacement (removing an old cap) | $200 – $400 | Condition of old cap, flue tile damage underneath |
| Copper or custom-fabricated cap | $350 – $900 | Material, number of flues, custom sizing |
| Crown coating (sound crown, hairline cracks) | $250 – $550 | Crown size and access |
| Crown repair or partial rebuild | $400 – $900 | Extent of cracking, mortar work needed |
What moves you up or down that range: the number of flues, whether the roof is walkable or needs staging, and whether the crown is a coating job or a rebuild. A cape-style roof in Midwood or a steeper pitch near Marine Park changes how much setup the job needs. To avoid overpaying, get a written flat price before work starts, and ask what the estimate includes: removal of the old cap, new sealant, and cleanup are all part of the quote. Our estimates are free, nothing is recommended without evidence you can see, and we’ll tell you when a repair can safely wait.
Chimney Cap & Crown Near Gravesend – Our Service Area
We work across Gravesend and the surrounding neighborhoods: Bensonhurst, Sheepshead Bay, Brighton Beach, Coney Island, Midwood, Dyker Heights, Flatlands, Borough Park, Marine Park, Mill Basin and Bergen Beach. Most jobs in these areas are booked within a few days, and same-day visits are possible where the schedule allows. If you’re nearby and need the same service, see our chimney cap & crown and chimney cap & crown pages for those areas, or start with chimney sweep in Gravesend if the flue needs cleaning too.
Serving Gravesend, NY – Our Local Coverage Area
We serve Gravesend and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Gravesend
A chimney cap is the fitted cover over the flue opening that keeps out rain, animals and sparks. The crown is the sloped concrete or mortar top of the masonry that sheds water away from the brick. Together they’re the weatherproofing layer at the top of your chimney, and when either one fails, water gets into places that are expensive to dry out.
Most cap installations and replacements finish in a couple of hours on site. Crown coating is similar, while a crown rebuild takes longer because the mortar has to be built up and shaped. The exact time depends on roof access and how many flues are involved, and we’ll give you a realistic window when we book the visit.
Typical estimated ranges run about $180 – $350 for a standard single-flue cap, $400 – $900 for a crown repair or partial rebuild, and $250 – $550 for crown coating. Custom or copper caps cost more. Your written estimate sets the final price, and estimates are free. Call (855) 342-5978 for an exact quote.
Yes. We fit and service Copperfield caps and work with Gelco components as well, along with DuraFlex liner systems and HeatShield resurfacing when the flue beneath the cap needs repair. We know where each of these wears first, so the inspection covers the right spots. If your cap is another make, we can still help.
Same-day visits are possible where the schedule allows, and we book jobs Sunday through Friday. We answer 24/7 on the phone, with fast dispatch from 7am to 7pm, and we’re closed Saturday. If a cap fails on a Saturday, call and we’ll book you for Sunday.
Yes. Work on caps and crowns carries a satisfaction guarantee, and we’ll explain what’s covered on your job when we give the estimate. If something isn’t right after a repair, get in touch and we’ll sort it out.
Clear access to the chimney at ground level if possible, and let us know about any pets, gate codes or parking restrictions. Make a note of anything you’ve noticed inside the house, like water in the firebox or a damper that sticks. That helps us decide what to check first when we arrive.
Schedule Your Chimney Cap & Crown Service in Gravesend Today
Call (855) 342-5978 to book a cap or crown visit in Gravesend. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. You get a free, no-obligation estimate, a flat price agreed before we start, and a straight answer on what needs fixing now and what can wait. One specialist for the full chimney, from chimney cap & crown work through sweeping and repair. See our chimney repair and chimney inspection pages if you need those checks first.
Written by the team at Chimney Sweep Gravesend.